View EPM3128ATC_157212.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MAX 3000A
(R)
Programmable Logic Device Family
Data Sheet
December 2002, ver. 3.2
Features...

High-performance, low-cost CMOS EEPROM-based programmable logic devices (PLDs) built on a MAX(R) architecture (see Table 1) 3.3-V in-system programmability (ISP) through the built-in IEEE Std. 1149.1 Joint Test Action Group (JTAG) interface with advanced pin-locking capability - ISP circuitry compliant with IEEE Std. 1532 Built-in boundary-scan test (BST) circuitry compliant with IEEE Std. 1149.1-1990 Enhanced ISP features: - Enhanced ISP algorithm for faster programming - ISP_Done bit to ensure complete programming - Pull-up resistor on I/O pins during in-system programming High-density PLDs ranging from 600 to 10,000 usable gates 4.5-ns pin-to-pin logic delays with counter frequencies of up to 227.3 MHz MultiVoltTM I/O interface enabling the device core to run at 3.3 V, while I/O pins are compatible with 5.0-V, 3.3-V, and 2.5-V logic levels Pin counts ranging from 44 to 256 in a variety of thin quad flat pack (TQFP), plastic quad flat pack (PQFP), plastic J-lead chip carrier (PLCC), and FineLine BGATM packages Hot-socketing support Programmable interconnect array (PIA) continuous routing structure for fast, predictable performance
Table 1. MAX 3000A Device Features Feature
Usable gates Macrocells Logic array blocks Maximum user I/O pins tPD (ns) tSU (ns) tCO1 (ns) fCNT (MHz)
EPM3032A
600 32 2 34 4.5 2.9 3.0 227.3
EPM3064A
1,250 64 4 66 4.5 2.8 3.1 222.2
EPM3128A
2,500 128 8 96 5.0 3.3 3.4 192.3
EPM3256A
5,000 256 16 158 7.5 5.2 4.8 126.6
EPM3512A
10,000 512 32 208 7.5 5.6 4.7 116.3
Altera Corporation
DS-MAX3000A-3.2
1
MAX 3000A Programmable Logic Device Family Data Sheet
...and More Features

PCI compatible Bus-friendly architecture including programmable slew-rate control Open-drain output option Programmable macrocell flipflops with individual clear, preset, clock, and clock enable controls Programmable power-saving mode for a power reduction of over 50% in each macrocell Configurable expander product-term distribution, allowing up to 32 product terms per macrocell Programmable security bit for protection of proprietary designs Enhanced architectural features, including: - 6 or 10 pin- or logic-driven output enable signals - Two global clock signals with optional inversion - Enhanced interconnect resources for improved routability - Programmable output slew-rate control Software design support and automatic place-and-route provided by Altera's development systems for Windows-based PCs and Sun SPARCstations, and HP 9000 Series 700/800 workstations Additional design entry and simulation support provided by EDIF 2 0 0 and 3 0 0 netlist files, library of parameterized modules (LPM), Verilog HDL, VHDL, and other interfaces to popular EDA tools from third-party manufacturers such as Cadence, Exemplar Logic, Mentor Graphics, OrCAD, Synopsys, Synplicity, and VeriBest Programming support with the Altera master programming unit (MPU), MasterBlasterTM communications cable, ByteBlasterMVTM parallel port download cable, BitBlasterTM serial download cable as well as programming hardware from third-party manufacturers and any in-circuit tester that supports JamTM Standard Test and Programming Language (STAPL) Files (.jam), Jam STAPL Byte-Code Files (.jbc), or Serial Vector Format Files (.svf)
General Description
MAX 3000A devices are low-cost, high-performance devices based on the Altera MAX architecture. Fabricated with advanced CMOS technology, the EEPROM-based MAX 3000A devices operate with a 3.3-V supply voltage and provide 600 to 10,000 usable gates, ISP, pin-to-pin delays as fast as 4.5 ns, and counter speeds of up to 227.3 MHz. MAX 3000A devices in the -4, -5, -6, -7, and -10 speed grades are compatible with the timing requirements of the PCI Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 2.2. See Table 2.
2
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Table 2. MAX 3000A Speed Grades Device -4
EPM3032A EPM3064A EPM3128A EPM3256A EPM3512A
Speed Grade -5 -6 -7 v v v v v v -10 v v v v v v v
The MAX 3000A architecture supports 100% transistor-to-transistor logic (TTL) emulation and high-density small-scale integration (SSI), medium-scale integration (MSI), and large-scale integration (LSI) logic functions. The MAX 3000A architecture easily integrates multiple devices ranging from PALs, GALs, and 22V10s to MACH and pLSI devices. MAX 3000A devices are available in a wide range of packages, including PLCC, PQFP, and TQFP packages. See Table 3. Table 3. MAX 3000A Maximum User I/O Pins Device 44-Pin PLCC
34 34
Note (1)
44-Pin TQFP
34 34
100-Pin 144-Pin 208-Pin 256-Pin TQFP TQFP PQFP FineLine BGA
66 80 96 116 158 172 208
EPM3032A EPM3064A EPM3128A EPM3256A EPM3512A Note:
(1)
When the IEEE Std. 1149.1 (JTAG) interface is used for in-system programming or boundary-scan testing, four I/O pins become JTAG pins.
MAX 3000A devices use CMOS EEPROM cells to implement logic functions. The user-configurable MAX 3000A architecture accommodates a variety of independent combinatorial and sequential logic functions. The devices can be reprogrammed for quick and efficient iterations during design development and debugging cycles, and can be programmed and erased up to 100 times.
Altera Corporation
3
MAX 3000A Programmable Logic Device Family Data Sheet
MAX 3000A devices contain 32 to 512 macrocells, combined into groups of 16 macrocells called logic array blocks (LABs). Each macrocell has a programmable-AND/fixed-OR array and a configurable register with independently programmable clock, clock enable, clear, and preset functions. To build complex logic functions, each macrocell can be supplemented with shareable expander and high-speed parallel expander product terms to provide up to 32 product terms per macrocell. MAX 3000A devices provide programmable speed/power optimization. Speed-critical portions of a design can run at high speed/full power, while the remaining portions run at reduced speed/low power. This speed/power optimization feature enables the designer to configure one or more macrocells to operate at 50% or lower power while adding only a nominal timing delay. MAX 3000A devices also provide an option that reduces the slew rate of the output buffers, minimizing noise transients when non-speed-critical signals are switching. The output drivers of all MAX 3000A devices can be set for 2.5 V or 3.3 V, and all input pins are 2.5-V, 3.3-V, and 5.0-V tolerant, allowing MAX 3000A devices to be used in mixed-voltage systems. MAX 3000A devices are supported by Altera development systems, which are integrated packages that offer schematic, text--including VHDL, Verilog HDL, and the Altera Hardware Description Language (AHDL)--and waveform design entry, compilation and logic synthesis, simulation and timing analysis, and device programming. The software provides EDIF 2 0 0 and 3 0 0, LPM, VHDL, Verilog HDL, and other interfaces for additional design entry and simulation support from other industry-standard PC- and UNIX-workstation-based EDA tools. The software runs on Windows-based PCs, as well as Sun SPARCstation, and HP 9000 Series 700/800 workstations.
f Functional Description
For more information on development tools, see the MAX+PLUS II Programmable Logic Development System & Software Data Sheet and the Quartus Programmable Logic Development System & Software Data Sheet. The MAX 3000A architecture includes the following elements:

Logic array blocks (LABs) Macrocells Expander product terms (shareable and parallel) Programmable interconnect array (PIA) I/O control blocks
The MAX 3000A architecture includes four dedicated inputs that can be used as general-purpose inputs or as high-speed, global control signals (clock, clear, and two output enable signals) for each macrocell and I/O pin. Figure 1 shows the architecture of MAX 3000A devices.
4
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 1. MAX 3000A Device Block Diagram
INPUT/GCLK1 INPUT/OE2/GCLK2 INPUT/OE1
INPUT/GCLRn 6 or 10 Output Enables (1) LAB A I/O Control Block 2 to 16 Macrocells 1 to 16 36 36 6 or 10 Output Enables (1) LAB B Macrocells 17 to 32 2 to 16 I/O Control Block
2 to 16 I/O
2 to 16 I/O
16 6 or 10 LAB C I/O Control Block 2 to 16 Macrocells 33 to 48 36 2 to 16 PIA
16 2 to 16 LAB D 36 Macrocells 49 to 64 2 to 16 I/O Control Block 6 or 10
2 to 16 I/O
2 to 16 I/O
16 6 or 10 2 to 16
16 2 to 16 6 or 10
Note:
(1) EPM3032A, EPM3064A, EPM3128A, and EPM3256A devices have six output enables. EPM3512A devices have 10 output enables.
Logic Array Blocks
The MAX 3000A device architecture is based on the linking of high-performance LABs. LABs consist of 16-macrocell arrays, as shown in Figure 1. Multiple LABs are linked together via the PIA, a global bus that is fed by all dedicated input pins, I/O pins, and macrocells. Each LAB is fed by the following signals:

36 signals from the PIA that are used for general logic inputs Global controls that are used for secondary register functions
Altera Corporation
5
MAX 3000A Programmable Logic Device Family Data Sheet
Macrocells
MAX 3000A macrocells can be individually configured for either sequential or combinatorial logic operation. Macrocells consist of three functional blocks: logic array, product-term select matrix, and programmable register. Figure 2 shows a MAX 3000A macrocell. Figure 2. MAX 3000A Macrocell
LAB Local Array Global Clear Parallel Logic Expanders (from other macrocells) Global Clocks 2 Programmable Register Register Bypass To I/O Control Block
PRN D/T Q
ProductTerm Select Matrix
VCC
Clock/ Enable Select
ENA CLRN
Clear Select
Shared Logic Expanders 36 Signals from PIA 16 Expander Product Terms
To PIA
Combinatorial logic is implemented in the logic array, which provides five product terms per macrocell. The product-term select matrix allocates these product terms for use as either primary logic inputs (to the OR and XOR gates) to implement combinatorial functions, or as secondary inputs to the macrocell's register preset, clock, and clock enable control functions. Two kinds of expander product terms ("expanders") are available to supplement macrocell logic resources:

Shareable expanders, which are inverted product terms that are fed back into the logic array Parallel expanders, which are product terms borrowed from adjacent macrocells
The Altera development system automatically optimizes product-term allocation according to the logic requirements of the design.
6 Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
For registered functions, each macrocell flipflop can be individually programmed to implement D, T, JK, or SR operation with programmable clock control. The flipflop can be bypassed for combinatorial operation. During design entry, the designer specifies the desired flipflop type; the Altera development system software then selects the most efficient flipflop operation for each registered function to optimize resource utilization. Each programmable register can be clocked in three different modes:

Global clock signal mode, which achieves the fastest clock-to-output performance. Global clock signal enabled by an active-high clock enable. A clock enable is generated by a product term. This mode provides an enable on each flipflop while still achieving the fast clock-to-output performance of the global clock. Array clock implemented with a product term. In this mode, the flipflop can be clocked by signals from buried macrocells or I/O pins.
Two global clock signals are available in MAX 3000A devices. As shown in Figure 1, these global clock signals can be the true or the complement of either of the two global clock pins, GCLK1 or GCLK2. Each register also supports asynchronous preset and clear functions. As shown in Figure 2, the product-term select matrix allocates product terms to control these operations. Although the product-term-driven preset and clear from the register are active high, active-low control can be obtained by inverting the signal within the logic array. In addition, each register clear function can be individually driven by the active-low dedicated global clear pin (GCLRn).
Expander Product Terms
Although most logic functions can be implemented with the five product terms available in each macrocell, highly complex logic functions require additional product terms. Another macrocell can be used to supply the required logic resources. However, the MAX 3000A architecture also offers both shareable and parallel expander product terms ("expanders") that provide additional product terms directly to any macrocell in the same LAB. These expanders help ensure that logic is synthesized with the fewest possible logic resources to obtain the fastest possible speed.
Altera Corporation
7
MAX 3000A Programmable Logic Device Family Data Sheet
Shareable Expanders
Each LAB has 16 shareable expanders that can be viewed as a pool of uncommitted single product terms (one from each macrocell) with inverted outputs that feed back into the logic array. Each shareable expander can be used and shared by any or all macrocells in the LAB to build complex logic functions. Shareable expanders incur a small delay (tSEXP). Figure 3 shows how shareable expanders can feed multiple macrocells. Figure 3. MAX 3000A Shareable Expanders
Shareable expanders can be shared by any or all macrocells in an LAB.
Macrocell Product-Term Logic
Product-Term Select Matrix
Macrocell Product-Term Logic
36 Signals from PIA
16 Shared Expanders
Parallel Expanders
Parallel expanders are unused product terms that can be allocated to a neighboring macrocell to implement fast, complex logic functions. Parallel expanders allow up to 20 product terms to directly feed the macrocell OR logic, with five product terms provided by the macrocell and 15 parallel expanders provided by neighboring macrocells in the LAB.
8
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
The Altera development system compiler can automatically allocate up to three sets of up to five parallel expanders to the macrocells that require additional product terms. Each set of five parallel expanders incurs a small, incremental timing delay (tPEXP ). For example, if a macrocell requires 14 product terms, the compiler uses the five dedicated product terms within the macrocell and allocates two sets of parallel expanders; the first set includes five product terms, and the second set includes four product terms, increasing the total delay by 2 x tPEXP. Two groups of eight macrocells within each LAB (e.g., macrocells 1 through 8 and 9 through 16) form two chains to lend or borrow parallel expanders. A macrocell borrows parallel expanders from lower- numbered macrocells. For example, macrocell 8 can borrow parallel expanders from macrocell 7, from macrocells 7 and 6, or from macrocells 7, 6, and 5. Within each group of eight, the lowest-numbered macrocell can only lend parallel expanders and the highest-numbered macrocell can only borrow them. Figure 4 shows how parallel expanders can be borrowed from a neighboring macrocell. Figure 4. MAX 3000A Parallel Expanders
Unused product terms in a macrocell can be allocated to a neighboring macrocell.
From Previous Macrocell
Preset Producter Select Matrix Clock Clear
Macrocell ProductTerm Logic
Preset ProductT Term Select Matrix Clock Clear
Macrocell ProductTerm Logic
36 Signals from PIA
16 Shared Expanders
To Next Macrocell
Altera Corporation
9
MAX 3000A Programmable Logic Device Family Data Sheet
Programmable Interconnect Array
Logic is routed between LABs on the PIA. This global bus is a programmable path that connects any signal source to any destination on the device. All MAX 3000A dedicated inputs, I/O pins, and macrocell outputs feed the PIA, which makes the signals available throughout the entire device. Only the signals required by each LAB are actually routed from the PIA into the LAB. Figure 5 shows how the PIA signals are routed into the LAB. An EEPROM cell controls one input to a two-input AND gate, which selects a PIA signal to drive into the LAB. Figure 5. MAX 3000A PIA Routing
To LAB
PIA Signals
While the routing delays of channel-based routing schemes in masked or FPGAs are cumulative, variable, and path-dependent, the MAX 3000A PIA has a predictable delay. The PIA makes a design's timing performance easy to predict.
I/O Control Blocks
The I/O control block allows each I/O pin to be individually configured for input, output, or bidirectional operation. All I/O pins have a tri-state buffer that is individually controlled by one of the global output enable signals or directly connected to ground or VCC. Figure 6 shows the I/O control block for MAX 3000A devices. The I/O control block has 6 or 10 global output enable signals that are driven by the true or complement of two output enable signals, a subset of the I/O pins, or a subset of the I/O macrocells.
10
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 6. I/O Control Block of MAX 3000A Devices
6 or 10 Global Output Enable Signals (1)
PIA
OE Select Multiplexer
VCC
to Other I/O Pins from Macrocell
GND
Open-Drain Output Slew-Rate Control
to PIA
Note:
(1) EPM3032A, EPM3064A, EPM3128A, and EPM3256A devices have six output enables. EPM3512A devices have 10 output enables.
When the tri-state buffer control is connected to ground, the output is tri-stated (high impedance), and the I/O pin can be used as a dedicated input. When the tri-state buffer control is connected to VCC, the output is enabled. The MAX 3000A architecture provides dual I/O feedback, in which macrocell and pin feedbacks are independent. When an I/O pin is configured as an input, the associated macrocell can be used for buried logic.
Altera Corporation
11
MAX 3000A Programmable Logic Device Family Data Sheet
In-System Programmability
MAX 3000A devices can be programmed in-system via an industry- standard four-pin IEEE Std. 1149.1-1990 (JTAG) interface. In-system programmability (ISP) offers quick, efficient iterations during design development and debugging cycles. The MAX 3000A architecture internally generates the high programming voltages required to program its EEPROM cells, allowing in-system programming with only a single 3.3-V power supply. During in-system programming, the I/O pins are tri-stated and weakly pulled-up to eliminate board conflicts. The pull-up value is nominally 50 k. MAX 3000A devices have an enhanced ISP algorithm for faster programming. These devices also offer an ISP_Done bit that ensures safe operation when in-system programming is interrupted. This ISP_Done bit, which is the last bit programmed, prevents all I/O pins from driving until the bit is programmed. ISP simplifies the manufacturing flow by allowing devices to be mounted on a printed circuit board (PCB) with standard pick-and-place equipment before they are programmed. MAX 3000A devices can be programmed by downloading the information via in-circuit testers, embedded processors, the MasterBlaster communications cable, the ByteBlasterMV parallel port download cable, and the BitBlaster serial download cable. Programming the devices after they are placed on the board eliminates lead damage on high-pin-count packages (e.g., QFP packages) due to device handling. MAX 3000A devices can be reprogrammed after a system has already shipped to the field. For example, product upgrades can be performed in the field via software or modem. The Jam STAPL programming and test language can be used to program MAX 3000A devices with in-circuit testers, PCs, or embedded processors.
f
For more information on using the Jam STAPL programming and test language, see Application Note 88 (Using the Jam Language for ISP & ICR via an Embedded Processor), Application Note 122 (Using Jam STAPL for ISP & ICR via an Embedded Processor) and AN 111 (Embedded Programming Using the 8051 and Jam Byte-Code). The ISP circuitry in MAX 3000A devices is compliant with the IEEE Std. 1532 specification. The IEEE Std. 1532 is a standard developed to allow concurrent ISP between multiple PLD vendors.
Programming with External Hardware f
12
MAX 3000A devices can be programmed on Windows-based PCs with an Altera Logic Programmer card, MPU, and the appropriate device adapter. The MPU performs continuity checking to ensure adequate electrical contact between the adapter and the device. For more information, see the Altera Programming Hardware Data Sheet.
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
The Altera software can use text- or waveform-format test vectors created with the Altera Text Editor or Waveform Editor to test the programmed device. For added design verification, designers can perform functional testing to compare the functional device behavior with the results of simulation. Data I/O, BP Microsystems, and other programming hardware manufacturers also provide programming support for Altera devices.
f IEEE Std. 1149.1 (JTAG) Boundary-Scan Support
For more information, see Programming Hardware Manufacturers. MAX 3000A devices include the JTAG BST circuitry defined by IEEE Std. 1149.1-1990. Table 4 describes the JTAG instructions supported by MAX 3000A devices. The pin-out tables found on the Altera web site (http://www.altera.com) or the Altera Digital Library show the location of the JTAG control pins for each device. If the JTAG interface is not required, the JTAG pins are available as user I/O pins.
Table 4. MAX 3000A JTAG Instructions JTAG Instruction
SAMPLE/PRELOAD EXTEST BYPASS
Description
Allows a snapshot of signals at the device pins to be captured and examined during normal device operation, and permits an initial data pattern output at the device pins Allows the external circuitry and board-level interconnections to be tested by forcing a test pattern at the output pins and capturing test results at the input pins Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass synchronously through a selected device to adjacent devices during normal device operation Selects the IDCODE register and places it between the TDI and TDO pins, allowing the IDCODE to be serially shifted out of TDO Selects the 32-bit USERCODE register and places it between the TDI and TDO pins, allowing the USERCODE value to be shifted out of TDO These instructions are used when programming MAX 3000A devices via the JTAG ports with the MasterBlaster, ByteBlasterMV, or BitBlaster cable, or when using a Jam STAPL file, JBC file, or SVF file via an embedded processor or test equipment
IDCODE USERCODE ISP Instructions
The instruction register length of MAX 3000A devices is 10 bits. The IDCODE and USERCODE register length is 32 bits. Tables 5 and 6 show the boundary-scan register length and device IDCODE information for MAX 3000A devices.
Altera Corporation
13
MAX 3000A Programmable Logic Device Family Data Sheet
Table 5. MAX 3000A Boundary-Scan Register Length Device
EPM3032A EPM3064A EPM3128A EPM3256A EPM3512A
Boundary-Scan Register Length
96 192 288 480 624
Table 6. 32-Bit MAX 3000A Device IDCODE Value Device Version (4 Bits)
EPM3032A EPM3064A EPM3128A EPM3256A EPM3512A Notes:
(1) (2)
Note (1)
IDCODE (32 bits) Part Number (16 Bits)
0111 0000 0011 0010 0111 0000 0110 0100 0111 0001 0010 1000 0111 0010 0101 0110 0111 0101 0001 0010
Manufacturer's 1 (1 Bit) Identity (11 Bits) (2)
00001101110 00001101110 00001101110 00001101110 00001101110 1 1 1 1 1
0001 0001 0001 0001 0001
The most significant bit (MSB) is on the left. The least significant bit (LSB) for all JTAG IDCODEs is 1.
f
See Application Note 39 (IEEE 1149.1 (JTAG) Boundary-Scan Testing in Altera Devices) for more information on JTAG BST.
14
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 7 shows the timing information for the JTAG signals. Figure 7. MAX 3000A JTAG Waveforms
TMS
TDI t JCP t JCH TCK tJPZX TDO tJSSU Signal to Be Captured Signal to Be Driven tJSH t JPCO t JPXZ t JCL t JPSU t JPH
tJSZX
tJSCO
tJSXZ
Table 7 shows the JTAG timing parameters and values for MAX 3000A devices. Table 7. JTAG Timing Parameters & Values for MAX 3000A Devices Symbol
tJCP tJCH tJCL tJPSU tJPH tJPCO tJPZX tJPXZ tJSSU tJSH tJSCO tJSZX tJSXZ TCK clock period TCK clock high time TCK clock low time JTAG port setup time JTAG port hold time JTAG port clock to output JTAG port high impedance to valid output JTAG port valid output to high impedance Capture register setup time Capture register hold time Update register clock to output Update register high impedance to valid output Update register valid output to high impedance 20 45 25 25 25
Parameter
Min
100 50 50 20 45
Max
Unit
ns ns ns ns ns
25 25 25
ns ns ns ns ns ns ns ns
Altera Corporation
15
MAX 3000A Programmable Logic Device Family Data Sheet
Programmable Speed/Power Control
MAX 3000A devices offer a power-saving mode that supports low-power operation across user-defined signal paths or the entire device. This feature allows total power dissipation to be reduced by 50% or more because most logic applications require only a small fraction of all gates to operate at maximum frequency. The designer can program each individual macrocell in a MAX 3000A device for either high-speed or low-power operation. As a result, speed-critical paths in the design can run at high speed, while the remaining paths can operate at reduced power. Macrocells that run at low power incur a nominal timing delay adder (tLPA) for the tLAD, tLAC, tIC, tACL, tEN, tCPPW and tSEXP parameters.
Output Configuration
MAX 3000A device outputs can be programmed to meet a variety of system-level requirements.
MultiVolt I/O Interface
The MAX 3000A device architecture supports the MultiVolt I/O interface feature, which allows MAX 3000A devices to connect to systems with differing supply voltages. MAX 3000A devices in all packages can be set for 2.5-V, 3.3-V, or 5.0-V I/O pin operation. These devices have one set of VCC pins for internal operation and input buffers (VCCINT), and another set for I/O output drivers (VCCIO). The VCCIO pins can be connected to either a 3.3-V or 2.5-V power supply, depending on the output requirements. When the VCCIO pins are connected to a 2.5-V power supply, the output levels are compatible with 2.5-V systems. When the VCCIO pins are connected to a 3.3-V power supply, the output high is at 3.3 V and is therefore compatible with 3.3-V or 5.0-V systems. Devices operating with VCCIO levels lower than 3.0 V incur a nominally greater timing delay of tOD2 instead of tOD1. Inputs can always be driven by 2.5-V, 3.3-V, or 5.0-V signals. Table 8 summarizes the MAX 3000A MultiVolt I/O support. Table 8. MAX 3000A MultiVolt I/O Support VCCIO Voltage 2.5
2.5 3.3 Note:
(1) When VCCIO is 3.3 V, a MAX 3000A device can drive a 2.5-V device that has 3.3-V tolerant inputs.
Input Signal (V) 3.3 v v 5.0 v v v v
Output Signal (V) 2.5 v v v v 3.3 5.0
16
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Open-Drain Output Option
MAX 3000A devices provide an optional open-drain (equivalent to open-collector) output for each I/O pin. This open-drain output enables the device to provide system-level control signals (e.g., interrupt and write enable signals) that can be asserted by any of several devices. It can also provide an additional wired-OR plane. Open-drain output pins on MAX 3000A devices (with a pull-up resistor to the 5.0-V supply) can drive 5.0-V CMOS input pins that require a high VIH. When the open-drain pin is active, it will drive low. When the pin is inactive, the resistor will pull up the trace to 5.0 V, thereby meeting CMOS requirements. The open-drain pin will only drive low or tri-state; it will never drive high. The rise time is dependent on the value of the pull-up resistor and load impedance. The IOL current specification should be considered when selecting a pull-up resistor
Slew-Rate Control
The output buffer for each MAX 3000A I/O pin has an adjustable output slew rate that can be configured for low-noise or high-speed performance. A faster slew rate provides high-speed transitions for high-performance systems. However, these fast transitions may introduce noise transients into the system. A slow slew rate reduces system noise, but adds a nominal delay of 4 to 5 ns. When the configuration cell is turned off, the slew rate is set for low-noise performance. Each I/O pin has an individual EEPROM bit that controls the slew rate, allowing designers to specify the slew rate on a pin-by-pin basis. The slew rate control affects both the rising and falling edges of the output signal.
Design Security
All MAX 3000A devices contain a programmable security bit that controls access to the data programmed into the device. When this bit is programmed, a design implemented in the device cannot be copied or retrieved. This feature provides a high level of design security because programmed data within EEPROM cells is invisible. The security bit that controls this function, as well as all other programmed data, is reset only when the device is reprogrammed. MAX 3000A devices are fully tested. Complete testing of each programmable EEPROM bit and all internal logic elements ensures 100% programming yield. AC test measurements are taken under conditions equivalent to those shown in Figure 8. Test patterns can be used and then erased during early stages of the production flow.
Generic Testing
Altera Corporation
17
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 8. MAX 3000A AC Test Conditions
Power supply transients can affect AC measurements. Simultaneous transitions of multiple outputs should be avoided for accurate measurement. Threshold tests must not be performed under AC conditions. Large-amplitude, fast- ground-current transients normally occur as the device outputs discharge the load capacitances. When these transients flow through the parasitic inductance between the device ground pin and the test system ground, significant reductions in observable noise immunity can result. Numbers in brackets are for 2.5-V outputs. Numbers without brackets are for 3.3-V devices or outputs.
VCC 703 [521 ] Device Output
To Test System
620 [481 ] Device input rise and fall times < 2 ns
C1 (includes jig capacitance)
Operating Conditions
Tables 9 through 12 provide information on absolute maximum ratings, recommended operating conditions, DC operating conditions, and capacitance for MAX 3000A devices. Note (1) Min
-0.5 -2.0 -25 No bias Under bias PQFP and TQFP packages, under bias -65 -65
Table 9. MAX 3000A Device Absolute Maximum Ratings Symbol
VCC VI IOUT TSTG TA TJ
Parameter
Supply voltage DC input voltage DC output current, per pin Storage temperature Ambient temperature Junction temperature
Conditions
With respect to ground (2)
Max
4.6 5.75 25 150 135 135
Unit
V V mA C C C
18
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Table 10. MAX 3000A Device Recommended Operating Conditions Symbol
VCCINT VCCIO
Parameter
Supply voltage for internal logic and (10) input buffers Supply voltage for output drivers, 3.3-V operation Supply voltage for output drivers, 2.5-V operation
Conditions
Min
3.0 3.0 2.3 3.0
Max
3.6 3.6 2.7 3.6 5.75 VCCIO 70 90 40 40
Unit
V V V V V V C C ns ns
VCCISP VI VO TA TJ tR tF
Supply voltage during ISP Input voltage Output voltage Ambient temperature Junction temperature Input rise time Input fall time For commercial use For commercial use (3)
-0.5 0 0 0
Table 11. MAX 3000A Device DC Operating Conditions Symbol
VIH VIL VOH
Note (4) Min
1.7 -0.5
Parameter
High-level input voltage Low-level input voltage 3.3-V high-level TTL output voltage 3.3-V high-level CMOS output voltage 2.5-V high-level output voltage
Conditions
Max
5.75 0.8
Unit
V V V V V V V
IOH = -8 mA DC, VCCIO = 3.00 V (5) IOH = -0.1 mA DC, VCCIO = 3.00 V (5) IOH = -100 A DC, VCCIO = 2.30 V (5) IOH = -1 mA DC, VCCIO = 2.30 V (5) IOH = -2 mA DC, VCCIO = 2.30 V (5)
2.4 VCCIO - 0.2 2.1 2.0 1.7 0.4 0.2 0.2 0.4 0.7 -10 -10 20 10 10 74
VOL
3.3-V low-level TTL output voltage IOL = 8 mA DC, VCCIO = 3.00 V (6) 3.3-V low-level CMOS output voltage 2.5-V low-level output voltage IOL = 0.1 mA DC, VCCIO = 3.00 V (6) IOL = 100 A DC, VCCIO = 2.30 V (6) IOL = 1 mA DC, VCCIO = 2.30 V (6) IOL = 2 mA DC, VCCIO = 2.30 V (6)
V V V V V A A k
II IOZ RI S P
Input leakage current Tri-state output off-state current Value of I/O pin pull-up resistor when programming in-system or during power-up
V I = -0.5 to 5.5 V (7) VI = -0.5 to 5.5 V (7) VC C I O = 2.3 to 3.6 V (8)
Altera Corporation
19
MAX 3000A Programmable Logic Device Family Data Sheet
Table 12. MAX 3000A Device Capacitance Symbol
CIN CI/O
Note (9) Conditions Min Max
8 8
Parameter
Input pin capacitance I/O pin capacitance
Unit
pF pF
VIN = 0 V, f = 1.0 MHz VOUT = 0 V, f = 1.0 MHz
Notes to tables:
(1) (2) See the Operating Requirements for Altera Devices Data Sheet. Minimum DC input voltage is -0.5 V. During transitions, the inputs may undershoot to -2.0 V or overshoot to 5.75 V for input currents less than 100 mA and periods shorter than 20 ns. (3) All pins, including dedicated inputs, I/O pins, and JTAG pins, may be driven before VCCINT and VCCIO are powered. (4) These values are specified under the recommended operating conditions, as shown in Table 10 on page 19. (5) The parameter is measured with 50% of the outputs each sourcing the specified current. The IOH parameter refers to high-level TTL or CMOS output current. (6) The parameter is measured with 50% of the outputs each sinking the specified current. The IOL parameter refers to low-level TTL, PCI, or CMOS output current. (7) This value is specified during normal device operation. During power-up, the maximum leakage current is 300 A. (8) This pull-up exists while devices are programmed in-system and in unprogrammed devices during power-up. (9) Capacitance is measured at 25 C and is sample-tested only. The OE1 pin (high-voltage pin during programming) has a maximum capacitance of 20 pF. (10) The POR time for all MAX 3000A devices does not exceed 100 s. The sufficient VCCINT voltage level for POR is 3.0 V. The device is fully initialized within the POR time after VCCINT reaches the sufficient POR voltage level.
Figure 9 shows the typical output drive characteristics of MAX 3000A devices.
20
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 9. Output Drive Characteristics of MAX 3000A Devices
3.3 V
150
IOL
100
Typical IO Output Current (mA)
50
VCCINT = 3.3 V VCCIO = 3.3 V O Temperature = 25 C
IOH
0 0
1
2
3
4
VO Output Voltage (V)
2.5 V
150
IOL
Typical IO Output Current (mA)
100
VCCINT = 3.3 V VCCIO = 2.5 V O Temperature = 25 C
50
IOH
0 0
1
2
3
4
VO Output Voltage (V)
Power Sequencing & Hot-Socketing
Because MAX 3000A devices can be used in a mixed-voltage environment, they have been designed specifically to tolerate any possible power-up sequence. The VCCIO and VCCINT power planes can be powered in any order. Signals can be driven into MAX 3000A devices before and during power-up without damaging the device. In addition, MAX 3000A devices do not drive out during power-up. Once operating conditions are reached, MAX 3000A devices operate as specified by the user.
Altera Corporation
21
MAX 3000A Programmable Logic Device Family Data Sheet
Timing Model
MAX 3000A device timing can be analyzed with the Altera software, with a variety of popular industry-standard EDA simulators and timing analyzers, or with the timing model shown in Figure 10. MAX 3000A devices have predictable internal delays that enable the designer to determine the worst-case timing of any design. The software provides timing simulation, point-to-point delay prediction, and detailed timing analysis for device-wide performance evaluation.
Figure 10. MAX 3000A Timing Model
Internal Output Enable Delay t IOE Input Delay t IN PIA Delay t PIA Global Control Delay t GLOB Logic Array Delay t LAD Register Control Delay t LAC tIC t EN Shared Expander Delay t SEXP
Parallel Expander Delay t PEXP
Register Delay t SU tH t PRE t CLR t RD t COMB
Output Delay t OD1 t OD2 t OD3 t XZ t Z X1 t Z X2 t Z X3 I/O Delay tI O
The timing characteristics of any signal path can be derived from the timing model and parameters of a particular device. External timing parameters, which represent pin-to-pin timing delays, can be calculated as the sum of internal parameters. Figure 11 shows the timing relationship between internal and external delay parameters.
22
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 11. MAX 3000A Switching Waveforms
tR & tF < 2 ns. Inputs are driven at 3 V for a logic high and 0 V for a logic low. All timing characteristics are measured at 1.5 V.
Combinatorial Mode
tIN Input Pin tIO I/O Pin tPIA PIA Delay tSEXP Shared Expander Delay tLAC , tLAD Logic Array Input tPEXP Parallel Expander Delay tCOMB Logic Array Output tOD Output Pin
Global Clock Mode
Global Clock Pin Global Clock at Register tSU Data or Enable (Logic Array Output) tR tIN tCH tCL tF
tGLOB tH
Array Clock Mode
tR Input or I/O Pin tIN tIO Clock into PIA Clock into Logic Array Clock at Register Data from Logic Array tRD Register to PIA to Logic Array tOD Register Output to Pin tOD tPIA tCLR , tPRE tPIA tPIA tACH tACL tF
tIC tSU tH
Altera Corporation
23
MAX 3000A Programmable Logic Device Family Data Sheet
Tables 13 through 20 show EPM3032A, EPM3064A, EPM3128A, EPM3256A, and EPM3512A timing information. Table 13. EPM3032A External Timing Parameters Symbol Parameter Conditions -4 Min
tPD1 tPD2 tSU tH tCO1 tCH tCL tASU tAH tACO1 tACH tACL tCPPW tCNT fCNT tACNT fACNT Input to non- registered output I/O input to non- registered output Global clock setup time C1 = 35 pF (2) C1 = 35 pF (2) (2) 2.9 0.0 1.0 2.0 2.0 1.6 0.3 1.0 2.0 2.0 (3) 2.0 4.4 227.3 4.4 227.3 138.9 138.9 7.2 103.1 4.3 (2) C1 = 35 pF (2) 3.0
Note (1) Speed Grade -7 Max
4.5 4.5 4.7 0.0 1.0 3.0 3.0 2.5 0.5 1.0 3.0 3.0 3.0 7.2 103.1 9.7 7.2 5.0
Unit -10
Min
Max
7.5 7.5
Min
Max
10 10 ns ns ns ns 6.7 ns ns ns ns ns 9.4 ns ns ns ns 9.7 ns MHz ns MHz
6.3 0.0 1.0 4.0 4.0 3.6 0.5 1.0 4.0 4.0 4.0
Global clock hold time (2) Global clock to output C1 = 35 pF delay Global clock high time Global clock low time Array clock setup time (2) Array clock hold time Array clock to output delay Array clock high time Array clock low time Minimum pulse width for clear and preset
Minimum global clock (2) period Maximum internal (2), (4) global clock frequency Minimum array clock period (2)
Maximum internal (2), (4) array clock frequency
24
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Table 14. EPM3032A Internal Timing Parameters (Part 1 of 2) Symbol Parameter Conditions -4 Min
tIN tIO tSEXP tPEXP tLAD tLAC tIOE tOD1 Input pad and buffer delay I/O input pad and buffer delay Shared expander delay Parallel expander delay Logic array delay Logic control array delay Internal output enable delay Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF
Note (1) Speed Grade -7 Max
0.7 0.7 1.9 0.5 1.5 0.6 0.0 0.8
Unit -10
Min
Max
1.2 1.2 3.1 0.8 2.5 1.0 0.0 1.3
Min
Max
1.5 1.5 4.0 1.0 3.3 1.2 0.0 1.8 ns ns ns ns ns ns ns ns
tOD2
C1 = 35 pF
1.3
1.8
2.3
ns
tOD3
C1 = 35 pF
5.8
6.3
6.8
ns
tZX1
Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 3.3 V Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 2.5 V Output buffer enable delay, C1 = 35 pF slow slew rate = on VCCIO = 2.5 V or 3.3 V Output buffer disable delay C1 = 5 pF Register setup time Register hold time Register delay Combinatorial delay Array clock delay Register enable time Global control delay Register preset time 1.3 0.6
4.0
4.0
5.0
ns
tZX2
4.5
4.5
5.5
ns
tZX3
9.0
9.0
10.0
ns
tXZ tSU tH tRD tCOMB tIC tEN tGLOB tPRE
4.0 2.0 1.0 0.7 0.6 1.2 0.6 0.8 1.2
4.0 2.8 1.3 1.2 1.0 2.0 1.0 1.3 1.9
5.0
ns ns ns
1.5 1.3 2.5 1.2 1.9 2.6
ns ns ns ns ns ns
Altera Corporation
25
MAX 3000A Programmable Logic Device Family Data Sheet
Table 14. EPM3032A Internal Timing Parameters (Part 2 of 2) Symbol Parameter Conditions -4 Min
tCLR tPIA tLPA Register clear time PIA delay Low-power adder (2) (5)
Note (1) Speed Grade -7 Max
1.2 0.9 2.5
Unit -10
Min
Max
1.9 1.5 4.0
Min
Max
2.6 2.1 5.0 ns ns ns
Table 15. EPM3064A External Timing Parameters Symbol Parameter Conditions
Note (1) Speed Grade -4 Min Max
4.5 4.5 2.8 0.0 1.0 2.0 2.0 3.1 4.7 0.0 1.0 3.0 3.0 2.6 0.4 4.3 1.0 3.0 3.0 3.0 4.5 222.2 4.5 222.2 135.1 135.1 7.4 100.0 7.4 100.0 10.0 7.2 5.1
Unit -10
-7 Min Max
7.5 7.5 6.2 0.0 1.0 4.0 4.0 3.6 0.6 1.0 4.0 4.0 4.0
Min
Max
10.0 10.0 ns ns ns ns 7.0 ns ns ns ns ns 9.6 ns ns ns ns 10.0 ns MHz ns MHz
tPD1 tPD2 tSU tH tCO1 tCH tCL tASU tAH tACO1 tACH tACL tCPPW tCNT fCNT tACNT fACNT
Input to non-registered output
C1 = 35 pF (2)
I/O input to non-registered C1 = 35 pF (2) output Global clock setup time Global clock hold time Global clock high time Global clock low time Array clock setup time Array clock hold time Array clock to output delay Array clock high time Array clock low time Minimum pulse width for clear and preset Minimum global clock period Maximum internal global clock frequency Maximum internal array clock frequency (3) (2) (2), (4) (2) (2) C1 = 35 pF (2) (2) (2)
Global clock to output delay C1 = 35 pF
1.6 0.3 1.0 2.0 2.0 2.0
Minimum array clock period (2) (2), (4)
26
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Table 16. EPM3064A Internal Timing Parameters (Part 1 of 2) Symbol Parameter Conditions -4 Min
tIN tIO tSEXP tPEXP tLAD tLAC tIOE tOD1 Input pad and buffer delay I/O input pad and buffer delay Shared expander delay Parallel expander delay Logic array delay Logic control array delay Internal output enable delay Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF
Note (1) Speed Grade -7 Max
0.6 0.6 1.8 0.4 1.5 0.6 0.0 0.8
Unit -10
Min
Max
1.1 1.1 3.0 0.7 2.5 1.0 0.0 1.3
Min
Max
1.4 1.4 3.9 0.9 3.2 1.2 0.0 1.8 ns ns ns ns ns ns ns ns
tOD2
C1 = 35 pF
1.3
1.8
2.3
ns
tOD3
C1 = 35 pF
5.8
6.3
6.8
ns
tZX1
Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 3.3 V Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 2.5 V Output buffer enable delay, C1 = 35 pF slow slew rate = on VCCIO = 2.5 V or 3.3 V Output buffer disable delay C1 = 5 pF Register setup time Register hold time Register delay Combinatorial delay Array clock delay Register enable time Global control delay Register preset time Register clear time 1.3 0.6
4.0
4.0
5.0
ns
tZX2
4.5
4.5
5.5
ns
tZX3
9.0
9.0
10.0
ns
tXZ tSU tH tRD tCOMB tIC tEN tGLOB tPRE tCLR
4.0 2.0 1.0 0.7 0.6 1.2 0.6 1.0 1.3 1.3
4.0 2.9 1.3 1.2 0.9 1.9 1.0 1.5 2.1 2.1
5.0
ns ns ns
1.6 1.3 2.5 1.2 2.2 2.9 2.9
ns ns ns ns ns ns ns
Altera Corporation
27
MAX 3000A Programmable Logic Device Family Data Sheet
Table 16. EPM3064A Internal Timing Parameters (Part 2 of 2) Symbol Parameter Conditions -4 Min
tPIA tLPA PIA delay Low-power adder (2) (5)
Note (1) Speed Grade -7 Max
1.0 3.5
Unit -10
Min
Max
1.7 4.0
Min
Max
2.3 5.0 ns ns
Table 17. EPM3128A External Timing Parameters Symbol Parameter Conditions
Note (1) Speed Grade -5 -7 Max
5.0 5.0
Unit -10
Min
tPD1 tPD2 tSU tH tCO1 tCH tCL tASU tAH tACO1 tACH tACL tCPPW tCNT fCNT tACNT fACNT Input to non- registered output I/O input to non- registered output Global clock setup time C1 = 35 pF (2) C1 = 35 pF (2) (2) 3.3 0.0 1.0 2.0 2.0 1.8 0.2 1.0 2.0 2.0 (3) 2.0 (2) C1 = 35 pF (2)
Min
Max
7.5 7.5
Min
Max
10 10 ns ns ns ns 6.6 ns ns ns ns ns 9.4 ns ns ns ns 10.2 ns MHz 10.2 ns MHz
4.9 0.0 3.4 1.0 3.0 3.0 2.8 0.3 4.9 1.0 3.0 3.0 3.0 5.2 7.7 129.9 5.2 7.7 129.9 7.1 5.0
6.6 0.0 1.0 4.0 4.0 3.8 0.4 1.0 4.0 4.0 4.0
Global clock hold time (2) Global clock to output C1 = 35 pF delay Global clock high time Global clock low time Array clock setup time (2) Array clock hold time Array clock to output delay Array clock high time Array clock low time Minimum pulse width for clear and preset
Minimum global clock (2) period Maximum internal (2), (4) global clock frequency Minimum array clock period (2) 192.3 192.3
98.0
Maximum internal (2), (4) array clock frequency
98.0
28
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Table 18. EPM3128A Internal Timing Parameters (Part 1 of 2) Symbol Parameter Conditions -5 Min
tIN tIO tSEXP tPEXP tLAD tLAC tIOE tOD1 Input pad and buffer delay I/O input pad and buffer delay Shared expander delay Parallel expander delay Logic array delay Logic control array delay Internal output enable delay Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF
Note (1) Speed Grade -7 Max
0.7 0.7 2.0 0.4 1.6 0.7 0.0 0.8
Unit -10
Min
Max
1.0 1.0 2.9 0.7 2.4 1.0 0.0 1.2
Min
Max
1.4 1.4 3.8 0.9 3.1 1.3 0.0 1.6 ns ns ns ns ns ns ns ns
tOD2
C1 = 35 pF
1.3
1.7
2.1
ns
tOD3
C1 = 35 pF
5.8
6.2
6.6
ns
tZX1
Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 3.3 V Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 2.5 V Output buffer enable delay, C1 = 35 pF slow slew rate = on VCCIO = 2.5 V or 3.3 V Output buffer disable delay C1 = 5 pF Register setup time Register hold time Register delay Combinatorial delay Array clock delay Register enable time Global control delay Register preset time Register clear time 1.4 0.6
4.0
4.0
5.0
ns
tZX2
4.5
4.5
5.5
ns
tZX3
9.0
9.0
10.0
ns
tXZ tSU tH tRD tCOMB tIC tEN tGLOB tPRE tCLR
4.0 2.1 1.0 0.8 0.5 1.2 0.7 1.1 1.4 1.4
4.0 2.9 1.3 1.2 0.9 1.7 1.0 1.6 2.0 2.0
5.0
ns ns ns
1.6 1.3 2.2 1.3 2.0 2.7 2.7
ns ns ns ns ns ns ns
Altera Corporation
29
MAX 3000A Programmable Logic Device Family Data Sheet
Table 18. EPM3128A Internal Timing Parameters (Part 2 of 2) Symbol Parameter Conditions -5 Min
tPIA tLPA PIA delay Low-power adder (2) (5)
Note (1) Speed Grade -7 Max
1.4 4.0
Unit -10
Min
Max
2.0 4.0
Min
Max
2.6 5.0 ns ns
Table 19. EPM3256A External Timing Parameters Symbol Parameter Conditions
Note (1) Speed Grade -7 Min Max
7.5 7.5 5.2 0.0 1.0 3.0 3.0 4.8 6.9 0.0 1.0 4.0 4.0 3.6 0.5 7.3 1.0 4.0 4.0 4.0 7.9 126.6 7.9 126.6 95.2 95.2 10.5 10.5 9.7 6.4
Unit -10
Min
Max
10 10 ns ns ns ns ns ns ns ns ns ns ns ns ns ns MHz ns MHz
tPD1 tPD2 tSU tH tCO1 tCH tCL tASU tAH tACO1 tACH tACL tCPPW tCNT fCNT tACNT fACNT
Input to non-registered output
C1 = 35 pF (2)
I/O input to non-registered C1 = 35 pF (2) output Global clock setup time Global clock hold time Global clock to output delay Global clock high time Global clock low time Array clock setup time Array clock hold time Array clock high time Array clock low time Minimum pulse width for clear and preset Minimum global clock period Maximum internal global clock frequency Minimum array clock period Maximum internal array clock frequency (3) (2) (2), (4) (2) (2), (4) (2) (2) (2) (2) C1 = 35 pF
2.7 0.3 1.0 3.0 3.0 3.0
Array clock to output delay C1 = 35 pF (2)
30
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Table 20. EPM3256A Internal Timing Parameters Symbol Parameter
Note (1) Speed Grade -7 Min Max
0.9 0.9 2.8 0.5 2.2 1.0 0.0
Conditions
Unit -10
Min
Max
1.2 1.2 3.7 0.6 2.8 1.3 0.0 1.6 ns ns ns ns ns ns ns ns
tIN tIO tSEXP tPEXP tLAD tLAC tIOE tOD1
Input pad and buffer delay I/O input pad and buffer delay Shared expander delay Parallel expander delay Logic array delay Logic control array delay Internal output enable delay Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF
1.2
tOD2
C1 = 35 pF
1.7
2.1
ns
tOD3
C1 = 35 pF
6.2
6.6
ns
tZX1 tZX2 tZX3
Output buffer enable delay, slow C1 = 35 pF slew rate = off VCCIO = 3.3 V Output buffer enable delay, slow C1 = 35 pF slew rate = off VCCIO = 2.5 V Output buffer enable delay, slow C1 = 35 pF slew rate = on VCCIO = 2.5 V or 3.3 V Output buffer disable delay Register setup time Register hold time Register delay Combinatorial delay Array clock delay Register enable time Global control delay Register preset time Register clear time PIA delay Low-power adder (2) (5) C1 = 5 pF 2.1 0.9
4.0 4.5 9.0
5.0 5.5 10.0
ns ns ns
tXZ tSU tH tRD tCOMB tIC tEN tGLOB tPRE tCLR tPIA tLPA
4.0 2.9 1.2 1.2 0.8 1.6 1.0 1.5 2.3 2.3 2.4 4.0
5.0
ns ns ns
1.6 1.2 2.1 1.3 2.0 3.0 3.0 3.2 5.0
ns ns ns ns ns ns ns ns ns
Altera Corporation
31
MAX 3000A Programmable Logic Device Family Data Sheet
Table 21. EPM3512A External Timing Parameters Symbol Parameter
Note (1) Speed Grade -7 Min Max
7.5 7.5 5.6 0.0 3.0 0.0 7.6 0.0 3.0 0.0 4.7 1.0 4.0 4.0 3.5 0.3 7.8 1.0 4.0 4.0 4.0 8.6 116.3 8.6 116.3 87.0 87.0 11.5 11.5 10.4 6.3
Conditions
Unit -10
Min
Max
10.0 10.0 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns MHz ns MHz
tPD1 tPD2 tSU tH tFSU tFH tCO1 tCH tCL tASU tAH tACO1 tACH tACL tCPPW tCNT fCNT tACNT fACNT
Input to non-registered output I/O input to non-registered output Global clock setup time Global clock hold time Global clock setup time of fast input Global clock hold time of fast input Global clock to output delay Global clock high time Global clock low time Array clock setup time Array clock hold time Array clock to output delay Array clock high time Array clock low time Minimum pulse width for clear and preset Minimum global clock period Maximum internal global clock frequency Minimum array clock period Maximum internal array clock frequency
C1 = 35 pF (2) C1 = 35 pF (2) (2) (2)
C1 = 35 pF
1.0 3.0 3.0
(2) (2) C1 = 35 pF (2)
2.5 0.2 1.0 3.0 3.0
(3) (2) (2), (4) (2) (2), (4)
3.0
Table 22. EPM3512A Internal Timing Parameters (Part 1 of 3) Symbol Parameter Conditions
Note (1) Speed Grade -7 -10 Max
0.7 0.7 3.1
Unit
Min
tIN tIO tFIN Input pad and buffer delay I/O input pad and buffer delay Fast input delay
Min
Max
0.9 0.9 3.6 ns ns ns
32
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Table 22. EPM3512A Internal Timing Parameters (Part 2 of 3) Symbol Parameter Conditions
Note (1) Speed Grade -7 -10 Max
2.7 0.4 2.2 1.0 0.0
Unit
Min
tSEXP tPEXP tLAD tLAC tIOE tOD1 Shared expander delay Parallel expander delay Logic array delay Logic control array delay Internal output enable delay Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V Output buffer enable delay, slow slew rate = off VCCIO = 3.3 V Output buffer enable delay, slow slew rate = off VCCIO = 2.5 V Output buffer enable delay, slow slew rate = on VCCIO = 3.3 V Output buffer disable delay Register setup time Register hold time Register setup time of fast input Register hold time of fast input Register delay Combinatorial delay Array clock delay Register enable time Global control delay Register preset time Register clear time PIA delay (2) C1 = 35 pF
Min
Max
3.5 0.5 2.8 1.3 0.0 1.5 ns ns ns ns ns ns
1.0
tOD2
C1 = 35 pF
1.5
2.0
ns
tOD3
C1 = 35 pF
6.0
6.5
ns
tZX1
C1 = 35 pF
4.0
5.0
ns
tZX2
C1 = 35 pF
4.5
5.5
ns
tZX3
C1 = 35 pF
9.0
10.0
ns
tXZ tSU tH tFSU tFH tRD tCOMB tIC tEN tGLOB tPRE tCLR tPIA
C1 = 5 pF 2.1 0.6 1.6 1.4
4.0 3.0 0.8 1.6 1.4 1.3 0.6 1.8 1.0 1.7 1.0 1.0 3.0
5.0
ns ns ns ns ns
1.7 0.8 2.3 1.3 2.2 1.4 1.4 4.0
ns ns ns ns ns ns ns ns
Altera Corporation
33
MAX 3000A Programmable Logic Device Family Data Sheet
Table 22. EPM3512A Internal Timing Parameters (Part 3 of 3) Symbol Parameter Conditions
Note (1) Speed Grade -7 -10 Max
4.5
Unit
Min
tLPA
(1) (2) (3)
Min
Max
5.0 ns
Low-power adder
(5)
Notes to tables:
These values are specified under the recommended operating conditions, as shown in Table 10 on page 19. See Figure 11 on page 23 for more information on switching waveforms. These values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these devices, add an additional 0.1 ns to the PIA timing value. This minimum pulse width for preset and clear applies for both global clear and array controls. The tLPA parameter must be added to this minimum width if the clear or reset signal incorporates the tLAD parameter into the signal path. These parameters are measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB. The tLPA parameter must be added to the tLAD , tLAC, tIC, tEN, tSEXP, tACL, and tCPPW parameters for macrocells running in low-power mode.
(4) (5)
Power Consumption
Supply power (P) versus frequency (fMAX, in MHz) for MAX 3000A devices is calculated with the following equation: P = PINT + PIO = ICCINT x VCC + PIO The PIO value, which depends on the device output load characteristics and switching frequency, can be calculated using the guidelines given in Application Note 74 (Evaluating Power for Altera Devices). The ICCINT value depends on the switching frequency and the application logic. The ICCINT value is calculated with the following equation: ICCINT = (A x MCTON) + [B x (MCDEV - MCTON)] + (C x MCUSED x fMAX x togLC) The parameters in the ICCINT equation are:
34
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
MCTON MCDEV MCUSED fMAX togLC A, B, C
= = = = = =
Number of macrocells with the Turbo BitTM option turned on, as reported in the MAX+PLUS II Report File (.rpt) Number of macrocells in the device Total number of macrocells in the design, as reported in the RPT File Highest clock frequency to the device Average percentage of logic cells toggling at each clock (typically 12.5%) Constants (shown in Table 23)
Table 23. MAX 3000A ICC Equation Constants Device
EPM3032A EPM3064A EPM3128A EPM3256A EPM3512A
A
0.85 0.85 0.85 0.85 0.85
B
0.36 0.36 0.36 0.36 0.36
C
0.017 0.017 0.017 0.017 0.017
The ICCINT calculation provides an ICC estimate based on typical conditions using a pattern of a 16-bit, loadable, enabled, up/down counter in each LAB with no output load. Actual ICC should be verified during operation because this measurement is sensitive to the actual pattern in the device and the environmental operating conditions. Figures 12 and 13 show the typical supply current versus frequency for MAX 3000A devices.
Altera Corporation
35
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 12. ICC vs. Frequency for MAX 3000A Devices
EPM3032A
V CC = 3.3 V
Room Temperature
70 60 50
Typical I CC Active (mA)
High Speed
40 30 20 10
227.3 MHz
144.9 MHz
Non-Turbo
0
50
100
150
200
250
Frequency (MHz)
EPM3064A
V CC = 3.3 V
Room Temperature
140 120 100
Typical I CC Active (mA) 80
60 40 20
High Speed
222.2 MHz
125.0 MHz
Non-Turbo
0
50 100
150
200
250E
Frequency (MHz)
36
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 13. ICC vs. Frequency for MAX 3000A Devices
EPM3128A V CC = 3.3 V Room Temperature 210 180 150 Typical I CC Active (mA) 120 90 108.7 MHz 60 30 0 50
High Speed
192.3 MHz
Non-Turbo
100
150
200
250
Frequency (MHz)
EPM3256A V CC = 3.3 V Room Temperature 350 300 250 Typical I CC Active (mA) 172.4 MHz
High Speed
200 150 100 50 0 50 100 150 200 102.0 MHz
Non-Turbo
Frequency (MHz) EPM3512A
600
V CC = 3.3 V Room Temperature
116.3 MHz
500
400
High Speed
Typical I CC Active (mA)
300
76.3 MHz
200
Low Power
100
0
20
40
60
80
100
120
140
Frequency (MHz)
Altera Corporation
37
MAX 3000A Programmable Logic Device Family Data Sheet
Device Pin-Outs
See the Altera web site (http://www.altera.com) or the Altera Digital Library for pin-out information. Figures 14 through 18 show the package pin-out diagrams for MAX 3000A devices.
Figure 14. 44-Pin PLCC/TQFP Package Pin-Out Diagram
Package outlines not drawn to scale.
INPUT/OE2/GCLK2 INPUT/OE2/GCLK2
INPUT/GCLRn
INPUT/GCLRn
INPUT/GCLK1
INPUT/GCLK1
INPUT/OE1
INPUT/OE1
GND
GND
VCC
VCC
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Pin 1
39 38 37 36 35 I/O I/O/TDO I/O GND VCC I/O I/O I/O/TCK I/O GND I/O
Pin 34
6 I/O/TDI I/O I/O GND I/O I/O I/O/TMS I/O VCC I/O GND 7 8 9 10 11 12 13 14 15 16 17
54
3
2
1 44 43 42 41 40 I/O/TDI I/O I/O GND I/O I/O I/O/TMS I/O VCC I/O GND I/O I/O/TDO I/O GND VCC
EPM3032A EPM3064A
34 33 32 31 30 29
EPM3032A EPM3064A
I/O I/O I/O/TCK I/O GND I/O
18 19 20 21 22 23 24 25 26 27 28 I/O I/O I/O I/O I/O I/O I/O I/O GND VCC I/O I/O I/O I/O I/O I/O I/O I/O I/O GND
Pin 12
VCC
I/O
Pin 23
44-Pin PLCC
44-Pin TQFP
38
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 15. 100-Pin TQFP Package Pin-Out Diagram
Package outline not drawn to scale.
Pin 1 Pin 76
EPM3064A EPM3128A
Pin 26
Pin 51
Figure 16. 144-Pin TQFP Package Pin-Out Diagram
Package outline not drawn to scale.
Indicates location of Pin 1
Pin 1
Pin 109
EPM3128A EPM3256A
Pin 37
Pin 73
Altera Corporation
39
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 17. 208-Pin PQFP Package Pin-Out Diagram
Package outline not drawn to scale.
Pin 1 Pin 157
EPM3256A EPM3512A
Pin 53
Pin 105
40
Altera Corporation
MAX 3000A Programmable Logic Device Family Data Sheet
Figure 18. 256-Pin FineLine BGA Package Pin-Out Diagram
Package outline not drawn to scale.
A1 Ball Pad Corner
Indicates Location of Ball A1
A B C D E F G H
EPM3512A
J K L M N P R T 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Revision History
The information contained in the MAX 3000A Programmable Logic Device Data Sheet version 3.2 supersedes information published in previous versions. The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.2:
Version 3.2
Updated the EPM3512 ICC versus frequency graph in Figure 13.
Version 3.1
The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.1:

Updated timing information in Table 1 for the EPM3256A device. Updated Note (10) of Table 12.
Altera Corporation
41
MAX 3000A Programmable Logic Device Family Data Sheet
Version 3.0
The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.0:

Added EPM3512A device. Updated Tables 2 and 3.
101 Innovation Drive San Jose, CA 95134 (408) 544-7000 http://www.altera.com Applications Hotline: (800) 800-EPLD Customer Marketing: (408) 544-7104 Literature Services: lit_req@altera.com
Copyright (c) 2002 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo, specific device designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera Corporation in the U.S. and other countries. All other product or service names are the property of their respective holders. Altera products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services
42
Altera Corporation

▲Up To Search▲

Price & Availability of EPM3128ATC

	To Download EPM3128ATC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .